Being adapted
IMPORTANT: PerfectPower is an extremely accurate power and performance measurement tool, but like all measurement material, it needs to be correctly configured and used to deliver its results with an optimal accuracy, and it is therefore essential to read this guide before any first use, thank you for your understanding.
Note: As of Tuesday, May 23, 2023, this guide is exhaustive on the process of configuring and using PerfectPower for the four basic measurements it performs (power, accelerations, runs flying start, and speed). However, additional information remains to be provided (results, lap timer, performance simulator, and use of an external GPS in Bluetooth), and they will be provided on Wednesday, May 24, 2023. Thank you for your understanding.
I) Configuring the application (Setup)
IV) Measurement of power and performances
V) Results
VI) Lap Timer
VII) Performances Simulator
VIII) Use of an external GPS in Bluetooth
0) Introduction
Using properly PerfectPower comes down to following a typical four-point approach:
1) Properly configure the application (chapter I)
2) Properly configure the Car sheet (chapter II)
3) Properly mount the phone in the car (chapter III)
4) Properly measure, using the flattest and smoothest possible measurement road, and averaging TWO measurements performed in BOTH directions of the road (chapter IV)
Note: When you open the application for the first time, you are asked if you want to allow PerfectPower to use your location, as well as the frequency of this access (3 choices: "Allow Once", "Allow While Using App", or "Don't Allow"). Although it is obvious, please select the second choice "Allow While Using App"!
Définition of the five basic screens
PerfectPower has five basic screens, which you can always access via the menu bar located at the bottom of the screen, which has five icons. These screens are, from left to right:
1) Perfs screen (main screen and home screen): Accessible by pressing the Perfs icon (the 1st, on the left)
2) Track screen: Accessible by pressing the Track icon (the 2nd, in the middle-left)
3) Setup screen: Accessible by pressing the Setup icon (the 3rd, in the middle)
4) Cars screen: Accessible by pressing the Cars icon (the 4th, in the middle-right)
5) Results screen: Accessible by pressing the Results icon (the 5th, on the right)
I) Configuring the application (Setup)
Configuring the application is done in the Setup screen, accessible by pressing the Setup icon located at the bottom and in the middle of the screen (middle icon, the 3rd).
You must perform all the desired settings (depending on the type of measurement) from top to bottom, i.e.:
- the choice of units (all types of measurement)
- the choice of the correction norm (power measurements)
- the input of weather conditions (power measurements)
- the choice of runs flying start parameters (gear engaged, start and end speed)
All the necessary explanations are already given in the application, you just have to follow them.
II) Configuring the Car sheet
Configuring the Car sheet is done in the Cars screen, accessible by pressing the Cars icon located at the bottom and in the middle-right of the screen (4th icon).
The list of registered cars is displayed on the screen. It contains a default car on first use (Aston Martin DBS, PerfectPower's mascot). You must select the desired car by clicking on its row, or on the + row if you want to create a new car. You then access its sheet, which you will have to fill in completely. Once completed, you can return to the Cars screen by pressing the BACK button. Please note that the recording of data in memory is done when closing the input keyboard (pressing the blue button Done), so it is important to ALWAYS close it BEFORE leaving the Car sheet!
Note 1: To avoid the risk of saturating the internal memory of your smartphone, the number of cars is limited to 20, and the number of results per type (power, accelerations, runs flying start) and per car is limited to 10. However, the number of results will be increased to 50 from the next update (version 5.1).
Note 2: You can delete a Car sheet at any time: from the Cars screen, press the Edit button located at the top right: you will then see a red button appear to the left of each car. Press the one corresponding to the car to be deleted, a red button Delete then appears to the right of the car, and you must press it to permanently delete the car. You can then delete other cars by repeating the same operation. Do not forget at the end to press the Done button located at the top right to tell the application that you have finished your deletions.
Warning: This deletion operation is irreversible, and it deletes at the same time all the results associated with this car!
Basic data (8)
You must enter 8 basic data, necessary for power measurements:
- Car weight
- Engine Displacement
- Number of cylinders
- Transmission
- Tyres dimension
- Gear ratios
- Final ratio
- Cd.A
Plus a 9th: the additional weight, which corresponds to all the masses other than those of the car: yours of course (or that of all the occupants present in the car at the time of the power measurements if you are several), and that of eventual luggages, belongings, or tools.
All the information necessary to enter these 8 basic data is given in the Database section, which will also provide you with a link to the most reliable and complete automotive database in the world: The Automobile-Catalog
IMPORTANT: A link to this database will be added directly in the application (in the Car sheet, at the very bottom) in the next version 5.1.
Option: Calculation of the gear ratios
If you don't know the gear and final ratios of your car (car not present in the Automobile-Catalog database), or you want to check them, PerfectPower has an option called "Calculation of the gear ratios" specially created for this purpose! This option is at the bottom of the Car sheet, and it is accessible by pressing the blue button >>>.
To use it, you just need to measure the stabilized speeds on each gear at 3000 rpm with PerfectPower (GPS speed permanently displayed at the top of the Perfs screen), then enter them in the corresponding fields in this option (remember to close the small keyboard after typing), and finally press the "Calculation of the gear ratios" button located just below the fields: PerfectPower will then calculate your new gear ratios, and put them in the corresponding fields "Gear ratios" in the Car sheet!
A few remarks however:
- This calculation of the gear ratios is necessarily done for a given final ratio: it is the one that is entered in the "Final ratio" field when you access the option. Of course, it's possible that this isn't the right final ratio since if you use this option, it is probably because you know neither the gear ratios nor the final ratio of your car, but it does not pose any problem, and you can just as well leave the default value of 3.705 (Aston Martin DBS), or put another one of your choice (4 for example), and all the gear ratios will be calculated for this final ratio. Admittedly, these gear ratios will therefore not be the real ones but equivalent ratios calculated for the final ratio entered, which is therefore not the correct one either, but as said this does not pose any problem, because what counts to calculate the engine speed / wheels speed ratio is only the total ratio (= gear ratio * final ratio), and this total ratio will be perfectly good for all gears! Of course, if you know the real final ratio, fill it in and then PerfectPower will calculate your real gear ratios.
- It is not essential to take this reading for all the gears: the most important is to do it for the gear used for the power measurements, generally the 2nd. All you have to do then is leave all the other fields at their default values. Nevertheless, PerfectPower encourages you to do it for all gears, so that the performance simulator can work properly, if you use it of course.
- This option also works in the opposite direction, to allow you to check if the gear and final ratios that you have entered in the Car sheet are correct: indeed, when you access this option, PerfectPower calculates the real speeds at 3000 rpm on all gears and displays them in the corresponding fields of this option: you just need to compare these speeds with those you measured on the road by stabilizing at 3000 rpm on each gear: they must be equal at +- 1 km/h!
Measurement data (3)
You must enter 3 measurement data, defining the conditions of your power measurements:
- Gear selected
- Min rev
- Max rev
The power measurements must always be carried out on a single and well defined gear, from a minimum rev to a maximum rev, both allowing to cover the entire normal engine operating range, so you must obviously specify these three parameters to PerfectPower!
- Gear selected: Use only the 2nd or the 3rd with a serial car, knowing that what determines this parameter in priority is the measurement time, which must be ideally between 5 and 10 s. Which to schematize corresponds to the 2nd for cars under 300 hp, and the 3rd for the (rare!) others.
- Min rev:Use 2000 rpm in gasoline engine and 1500 rpm in Diesel engine, values typically used on chassis dynamometers and perfectly suited to these types of engines
- Max rev:Use the rev limiter in gasoline engine and the red zone in Diesel engine
A remark however: try to always measure in 2nd gear, even with a car over 300 hp, because on open road it can alas be difficult to find a sufficiently long, flat and smooth measurement road to allow correct measurements in 3rd gear, not to mention the obvious risk of... losing your licence! You should measure in 3rd gear ONLY in one of the three following cases:
- Measurement time REALLY well under 5 s (but then you have a real rocket!)
- Insufficient grip (of course, it is preferable to avoid measuring under the rain...)
- Voluntary limitation of the torque in 2nd gear on certain FWD sports cars (and not even really in fact: a Peugeot 2008 1.2 turbo 130 hp is in this case!)
Please note, however, that even in the 3rd case, the measurement in 3rd gear is NOT an obligation: it is ONLY if you wish to compare your engine power and torque results with those given by the manufacturer, which them have been carried out without torque limitation. But if you just wish to get reference results of your car in 2nd gear with the full awareness that they are voluntarily limited in this gear, it obviously doesn't pose any problem!
Note: PerfectPower calculates the theoretical max speed on your measurement gear (theoretical speed on the gear entered at the max rev entered), and displays it in green just below the 3 fields of the 3 measurement data (line "Speed at max rev"). This value is a precious help, as it will allow you to check at a glance during your power measurements if everything is OK (setting of the gear and final ratios and of the tyres dimension, quality of the GPS reception on your measurement road): indeed, the max speed actually measured by PerfectPower must match this theoretical max speed! Please note, however, that a tolerance margin of +- 2% must be granted to this value, corresponding to that on the actual tyres dimension (that on the gear and final ratios is negligible).
III) Mounting the phone
Mounting your phone is done by using a good windshield mount (i.e. sufficiently rigid, holding the phone correctly and correctly absorbing vibrations), and by positioning it correctly. No other type of mounting should be used!
The three rules that the phone must follow are:
- it must not move during the measurement (as little as possible in reality)
- it must be subjected to as little vibration as possible
- it must be aligned with the direction of movement of the vehicle and not tilted laterally, but can be tilted vertically between 0° and 90° in relation to the horizontal
The diagram below shows you the position the phone must have.
IMPORTANT: PerfectPower strongly recommends the use of the WIXGEAR universal magnetic windshield mount, which perfectly fulfills all the required criteria!
IV) Measurement of power and performances
You have to perform your measurements on the flattest and smoothest road possible (this is the most important), in straight line, with as little wind as possible, and with tires warm and well inflated (manufacturer's pressure).
It is also important to perform your measurements in both directions of the road (if possible of course) and ask PerfectPower to average them in order to eliminate the very real influence of the slope of the road and the wind on the results...
You are now presented in detail the four types of measurements that can be carried out with PerfectPower:
- 3 main and stored in memory: Power, Accelerations, and Runs flying start
- 1 secondary: Speed
1) Power
Go to the Perfs screen (the main screen, accessible by pressing the Perfs icon located at the bottom left of the screen), and at the very top of the screen, select:
- the Power tab (the 1st)
- the car you want to use (short click to scroll through them)
Car well stabilized at standstill, foot on the brake, disengaged and 1st gear engaged, press the chrono located in the middle of the screen.
The bar below the chrono initially blue ("Start") then turns red ("Wait") for 1 second, time during which you must not move (calibration of the accelerometer).
Then the bar turns green ("Go!"): you can then leave whenever you want, the application will identify the precise moment of the start, and the chrono will start immediately (white bar "Running...").
Normally start in 1st, then quickly put yourself on your measurement gear (the one you entered in the Car sheet for the power measurements, the 2nd or the 3rd), making sure to fall back on this gear below the min rev (also entered in the Car sheet).
Then fully accelerate (wide open throttle) to the max rev (also entered in the Car sheet), no more, no less.
As soon as this max rev is reached, immediately put yourself in freewheel (by disengaging the clutch) for at least three seconds, time after which the chrono will stop automatically. You can also brake a little to force it to stop.
In all cases, the chrono (and therefore the measurement) will stop automatically after the first of the three following conditions encountered: 3 consecutive seconds of deceleration, heavy braking, or 30 seconds of measurement. The end of the measurement is shown by the bar which turns blue again ("Ended").
A measurement report is then displayed in the lower part of the screen, which will give you the essential information about your measurement. Once read, press the chrono, the application will re-initialize for another measurement (blue bar "Start").
IMPORTANT 1: For an optimal curve end, it is preferable not to brake suddenly as soon as the max rev is reached (especially if you are not using an external GPS!), but to put yourself in freewheel (or just raise the foot in automatic gearbox) for at least a little second.
IMPORTANT 2: Above all, do not continue accelerating in the higher gear once the max rev has been reached in the measurement gear, otherwise the application will believe that the measurement is not finished and will continue to record it! This reflex is very common among new users!
Demonstration videos
PerfectPower demo video (official) - Audi S2 "Track" in "Normal Boost" config - Direction 1 (281 hp)
PerfectPower demo video - Audi S2 "Track" in "Normal Boost" config - Direction 2 (281 hp)
Tips & Tricks
Always stop your measurements at the same maximum rev (the one you have entered in the Car sheet) without exception (except in an emergency of course). Not only is this the normal measurement protocol, but it also allows you to detect AND above all be soon able to correct a weak GPS reception! Indeed:
- When you are not using an external GPS, the maximum speed of all your measurements must be within an amplitude of 2% maximum (example: 60 mph real ==> all speeds between 59.4 and 60.6 mph), and the maximum power in a same direction of measurement within an amplitude of 4% maximum (example: 100 hp real ==> all powers between 98 and 102 hp)
- When you use a high performance external GPS of 10 Hz minimum, these amplitudes change to respectively 1% and 2% maximum (example: 60 mph real ==> all speeds between 59.7 and 60.3 mph & 100 hp real ==> all powers between 99 and 101 hp)
Also, if your measurements do not fall within these speed and power amplitudes, it is the sure sign that your GPS reception is weak, but be aware that a future version of PerfectPower will integrate a unique (and almost magical!) function of re-calculation of the measurement on the real max speed at the end of the measurement, which you just will need to enter in the application!
2) Accelerations
Go to the Perfs screen (the main screen, accessible by pressing the Perfs icon located at the bottom left of the screen), and at the very top of the screen, select:
- the Accelerations tab (the 2nd)
- the car you want to use (short click to scroll through them)
Car well stabilized at standstill, foot on the brake, disengaged and 1st gear engaged, press the chrono located in the middle of the screen.
The bar below the chrono initially blue ("Start") then turns red ("Wait") for 1 second, time during which you must not move (calibration of the accelerometer).
Then the bar turns green ("Go!"): you can then leave whenever you want, the application will identify the precise moment of the start, and the chrono will start immediately (white bar "Running...").
Concerning the measurement itself, only one thing to do: fully accelerate, doing your best to break the clock (but not the application, anyway you would not succeed, even with 1000 hp!).
Once the measurement is finished, immediately put yourself in freewheel (by disengaging the clutch) for at least three seconds, time after which the chrono will stop automatically. You can also brake a little to force it to stop.
In all cases, the chrono (and therefore the measurement) will stop automatically after the first of the three following conditions encountered: 3 consecutive seconds of deceleration, heavy braking, or 60 seconds of measurement. The end of the measurement is shown by the bar which turns blue again ("Ended").
A measurement report is then displayed in the lower part of the screen, which will give you the essential information about your measurement. Once read, press the chrono, the application will re-initialize for another measurement (blue bar "Start").
3) Runs flying start
Go to the Perfs screen (the main screen, accessible by pressing the Perfs icon located at the bottom left of the screen), and at the very top of the screen, select:
- the Runs FS tab (the 3rd)
- the car you want to use (short click to scroll through them)
Stabilize at a real speed (GPS speed displayed at the top of the Perfs screen) 2 mph lower than the run start speed you entered in Setup & Runs flying start, by putting yourself in the gear you also filled in there, then press the chrono located in the middle of the screen.
The bar below the chrono initially blue ("Start") then turns green (“Go!”): you can then crush the accelerator whenever you want, the application will identify the precise moment of crossing the run start speed entered in Setup & Runs flying start, and the chrono will start immediately (white bar "Running...").
You must then stop accelerating only when you have exceeded the run end speed entered in Setup & Runs flying start, which will be achieved when the bar turns blue again ("Ended").
A measurement report is then displayed in the lower part of the screen, which will give you the essential information about your measurement. Once read, press the chrono, the application will re-initialize for another measurement (blue bar "Start").
4) Speed
The actual speed (GPS speed) is permanently displayed at the top of the Perfs screen (the main screen, accessible by pressing the Perfs icon located at the bottom left of the screen). This function actually allows to carry out three types of measurement:
- The measurement of the max speed: simply run your car at full speed (on German autobahn "of course"), and read the speed displayed by PerfectPower
- The speedometer calibration: stabilize your car at the desired speedometer speed (example: 60 mph), and read the speed displayed by PerfectPower
- A manual rev calibration for power measurements: stabilize your car at the PerfectPower calibration rev of 3000 rpm in the desired measurement gear (example: the 2nd), read the speed displayed by PerfectPower, and enter it in the "Calculation of the gear ratios" option available in your Car sheet
V) Results
VI) Lap Timer
VII) Performances Simulator
VIII) Use of an external GPS in Bluetooth